Trw2scan - Revision history

Peter: /* ECUs known to be supported */

2012-06-19T11:31:54Z

‎ECUs known to be supported

2012-06-19T11:30:59Z

2012-06-19T11:28:57Z

2012-06-19T11:27:45Z

2012-05-21T18:20:20Z

2012-05-15T13:43:14Z

2012-05-15T13:35:31Z

‎ECUs known to be supported

2012-05-06T19:38:37Z

‎ECUs known to be supported

2012-03-23T00:08:20Z

2012-03-23T00:07:35Z

@@ Line 23: / Line 23: @@
 |-
 | 60625181 || Alfa GTV phase 1 (Make sure L-line is not connected!)
 |}

@@ Line 9: / Line 9: @@
 =Hardware=
 trw2scan works with USB KKL-adapters based on FTDI's FT232 chip. There are many sources found on the web, one is stated below.
 To be able to connect to the GTV ph 1 (ECU 60625181) the L-line must NOT be connected. You need to modify either your KKL-adapter
@@ Line 26: / Line 28: @@
 '''ATTENTION:''' It is strongly recommended NOT to use this software while the airbags are connected to the ECU!
 For disconnecting follow the procedure proposed in the respective workshop manual. E.g. disconnect the battery and wait for 10 minutes before disconnecting the airbag.

@@ Line 24: / Line 24: @@
 =Safety Issues=
-It is strongly recommended NOT to use this software while the airbags ar connected to the ECU!
+'''ATTENTION:''' It is strongly recommended NOT to use this software while the airbags are connected to the ECU!
-For disconnecting follo the procedure proposed in the respective workshop manual. E.g. disconnect the battery and wait for 10 minutes before disconnecting the airbag.
+For disconnecting follow the procedure proposed in the respective workshop manual. E.g. disconnect the battery and wait for 10 minutes before disconnecting the airbag.
 Airbags should be replaced by 3.3Ohm "dummy" resistors in order to prevent the ECU from detecting the missing airbags.

← Older revision		Revision as of 11:27, 19 June 2012
Line 23:		Line 23:
	\|}		\|}

		+	=Safety Issues=
		+	It is strongly recommended NOT to use this software while the airbags ar connected to the ECU!
		+	For disconnecting follo the procedure proposed in the respective workshop manual. E.g. disconnect the battery and wait for 10 minutes before disconnecting the airbag.

		+	Airbags should be replaced by 3.3Ohm "dummy" resistors in order to prevent the ECU from detecting the missing airbags.
		+
		+
		+	=Disclaimer=
		+	Working on car electronics may cause severe damage and danger and has to be done by qualified personnel using qualified equipment and software.
		+
		+	trw2scan is no qualified tool suited to perform car repairs. The software is intended only for educational purposes demonstrating on board diagnosis protocols. The usage together with devices that are connected to car electronics or airbags is not recommended. The software is provided "as is" without warranty of any kind. Any liability for damages caused by using the software is excluded.

	=Links=		=Links=

← Older revision		Revision as of 18:20, 21 May 2012
Line 30:		Line 30:

	[http://autos.groups.yahoo.com/group/UniDiag/?v=1&t=directory&ch=web&pub=groups&sec=dir&slk=3 Homepage of the unidiag OBD software, also providing a KKL-adapter compatible with trw2scan]		[http://autos.groups.yahoo.com/group/UniDiag/?v=1&t=directory&ch=web&pub=groups&sec=dir&slk=3 Homepage of the unidiag OBD software, also providing a KKL-adapter compatible with trw2scan]
		+
		+	[http://www.youtube.com/watch?v=Ji8ICPtW8Yc Video demonstration of how to use trw2scan]
		+
		+	[http://www.alfaowner.com/Forum/alfa-gtv-and-916-spider/336600-phase-1-trw2-airbag-diagnostics-solved.html Discussion thread on alfaowner.com]

@@ Line 17: / Line 17: @@
 | 60631206 || Alfa 145/146
 |-
-| 60625181 || ??
+| 60625181 || Alfa GTV phase 1
 |}

@@ Line 6: / Line 6: @@
 trw2scan ''scriptfile''
 =ECUs known to be supported=
@@ Line 20: / Line 23: @@
 [http://www.peter-feil.eu/~peter/obd/trw2scan trw2scan download page]